Difference between revisions of "Orange Pi R1"
Jump to navigation
Jump to search
(Created page with "A variant of the Orange Pi Zero board that replaces a USB port with an RJ45 Ethernet module connected on the USB bus. == Board == === Upper side === File:OrangePiZero R...") |
|||
| (5 intermediate revisions by the same user not shown) | |||
| Line 1: | Line 1: | ||
| − | A variant of the [[Orange Pi Zero]] board that replaces a USB port with an RJ45 Ethernet module connected on the USB bus. | + | A variant of the [[Orange Pi Zero]] board that replaces a USB port with an [[RJ45]] Ethernet module connected on the USB bus. |
== Board == | == Board == | ||
=== Upper side === | === Upper side === | ||
[[File:OrangePiZero R1 front numbered.jpg|thumb]] | [[File:OrangePiZero R1 front numbered.jpg|thumb]] | ||
| − | { | + | {| class="wikitable" |
| + | |- | ||
| + | ! # !! Component | ||
| + | |- | ||
| + | | 1 || RJ45 Ethernet port connected as a USB device | ||
| + | |- | ||
| + | | 2 || RJ45 Ethernet port connected directly to the SoC | ||
| + | |- | ||
| + | | 3 || 26-pin GPIO | ||
| + | |- | ||
| + | | 4 || Serial port: GND, RX, TX (bottom to top) | ||
| + | |- | ||
| + | | 5 || Realtek [[RTL8152B]] USB Ethernet controller | ||
| + | |- | ||
| + | | 6 || ? | ||
| + | |- | ||
| + | | 7 || Realtek [[RTL8189ETV]] WiFi controller as a stamp module | ||
| + | |- | ||
| + | | 8 || 13-pin expansion port | ||
| + | |- | ||
| + | | 9 || WiFi antenna | ||
| + | |- | ||
| + | | 10 || [[Allwinner]] Technology [[H2+]] [[SoC]] | ||
| + | |- | ||
| + | | 11 || 256 MB [[DDR3]] [[SDRAM]] | ||
| + | |- | ||
| + | | 12 || micro-USB port (power and data, OTG) | ||
| + | |- | ||
| + | | 13 || ? LED | ||
| + | |- | ||
| + | | 14 || Power LED | ||
| + | |} | ||
=== Bottom side === | === Bottom side === | ||
[[File:OrangePiZero R1 back numbered.jpg|thumb]] | [[File:OrangePiZero R1 back numbered.jpg|thumb]] | ||
| − | { | + | {| class="wikitable" |
| + | |- | ||
| + | ! # !! Component | ||
| + | |- | ||
| + | | 1 || RJ45 Ethernet port connected directly to the SoC | ||
| + | |- | ||
| + | | 2 || RJ45 Ethernet port connected as a USB device | ||
| + | |- | ||
| + | | 3 || 26-pin GPIO | ||
| + | |- | ||
| + | | 4 || 16 MB SPI flash | ||
| + | |- | ||
| + | | 5 || micro-SD card slot | ||
| + | |} | ||
| + | |||
| + | == External Links == | ||
| + | * [https://www.armbian.com/orange-pi-r1/ Armbian page] | ||
| + | * [https://openwrt.org/toh/hwdata/xunlong/xunlong_orange_pi_r1 OpenWRT page] | ||
| + | * [https://github.com/hyphop/miZy miZy Minimalistic OS] | ||
| + | ** [https://forum.openwrt.org/t/xunlong-orange-pi-r1-boot-from-flash/57700 OpenWRT forum thread on using miZy] | ||
| + | * [https://learn.adafruit.com/circuitpython-on-orangepi-linux/orange-pi-r1 Adafruit tutorial for CircuitPython] | ||
Latest revision as of 06:28, 21 July 2020
A variant of the Orange Pi Zero board that replaces a USB port with an RJ45 Ethernet module connected on the USB bus.
Board
Upper side
| # | Component |
|---|---|
| 1 | RJ45 Ethernet port connected as a USB device |
| 2 | RJ45 Ethernet port connected directly to the SoC |
| 3 | 26-pin GPIO |
| 4 | Serial port: GND, RX, TX (bottom to top) |
| 5 | Realtek RTL8152B USB Ethernet controller |
| 6 | ? |
| 7 | Realtek RTL8189ETV WiFi controller as a stamp module |
| 8 | 13-pin expansion port |
| 9 | WiFi antenna |
| 10 | Allwinner Technology H2+ SoC |
| 11 | 256 MB DDR3 SDRAM |
| 12 | micro-USB port (power and data, OTG) |
| 13 | ? LED |
| 14 | Power LED |
Bottom side
| # | Component |
|---|---|
| 1 | RJ45 Ethernet port connected directly to the SoC |
| 2 | RJ45 Ethernet port connected as a USB device |
| 3 | 26-pin GPIO |
| 4 | 16 MB SPI flash |
| 5 | micro-SD card slot |
